Gene Cafe Dimmer Control Mod - Stage 1

Post about your favourite online roasters, roasted coffees and green bean sources
Post Reply
Claudette
Posts: 21
Joined: Tue Aug 20, 2019 3:20 pm

Gene Cafe Dimmer Control Mod - Stage 1 - By Dave Corbey
Enable the Gene to progressively lower the power applied to the heating element, so that rather than switching it on and off, it simply got less hot, minimising the temperature gradient within the drum and the overall maximum temperatures the beans are subjected to near the inlet end of the roasting chamber.
    Target cost = less than £25
      Difficulty = easy
        Time to complete = less than 1 hour (it can be done in 30 minutes)
          Fully Reversible = yes
            Benefits:

            overall temperatures within the Gene would be reduced extending component life and heating element life, because maximum temperatures are reduced overall.
            More accurate profiling of temperature within the roaster at and beyond 1st crack
            Limited ability to control the ramp up of temperature
            Better Roasts
            If you do have a pre March 07 Gene with a 230V element, you will probably get better (and faster) roasts and prolong heating element life.
            Image
            STAGE 1
            Warning: a reasonable level of competence is required and no guarantee is given that these guidelines are error free, you undertake all work at your own risk, we take no responsibility for anything that happens

            Dimmer Control Modification

            Equipment required
            Crimping Tool and 1 x spade male, 1 x spade female1
            3-4 feet of black 3 core electrical cable
            2 x 47mm Pattress Boxes (£1.19 each Wickes)…more space for cooling
            Single pole 2 way light switch 10 amp rating (£1.19 Wickes)..I was cheap and bought a 6 amp switch, but wish I had bought a 10 amp.
            Varilight 1000W standard dimmer (white) model HQ9W (18.63 inc delivery and VAT from http://www.theinternetelectricalstore.c ... -115-p.asp)
            Piece of Aluminium sheeting 0.5-1mm thick, 150-180 mm long and approx 40mm wide. You should be able to scrounge an off cut for a few pence, or grab a piece at a local scrap dealer or municipal dump.
            Some Duck tape
            Optional (soldering Iron to tin ends of wire)
            Plug-In Power and Energy Monitor (I assume you already have one of these)2
            Assuming you have most of the bits and bobs such as connectors and duck tape, the cost of the project will be around £23 or less. The Varilight dimmer (http://www.varilight.co.uk/) has been specially selected as its high quality of construction allows for easy and simple modification, with the minimum of work and risk to the component (I am not sure how well other manufacturers dimmers will work).3

            Modify the dimmer
            Add some extra heat sink capability. First pull off the knob and undo the nut as shown by the arrows. This will allow you to remove the dimmer module and it’s heat sink.

            Image
            You want to end up with something that looks like the diagram below. The piece of Aluminium simply has a hole drilled out (elongated hole is better) and is bent as shown below. The hole is large enough for the threaded part of the dimmer module (the part the but screwed on to earlier) to be passed through it and the replaced and re-tightened. As long as your piece of Aluminium is flat and not too thick. The existing heat sink of the dimmer is in full contact with it and when the module is replaced sufficient pressure is applied to form an excellent thermal contact area. You will actually be able to use a heat sink much smaller than mine e.g. omit the folding back on itself….me I just like IKB type design.
            Image
            Your dimmer should look something like this…Congratulations, your dimmer will now easily handle the 1250+ watts of the heating element with no problems or further modification required. I should add though that it is extremely important to have a good contact between the extra heat sink and the existing heat sink of the dimmer and ideally, use thermal past at the junction of the two heat sinks.
            Image
            Main wiring for the Gene
            Disassemble the Gene as shown (See GeneCafe Heater Unit Replacement) The overview of what you need to do is shown here. Note: The earth cable is trimmed off as we have no need or use for it.
            Image
            The inside of your Gene will end up looking like this
            Image
            Use a drill with a HSS (High Speed Steel) bit to drill holes in the pattress boxes, one for the cable from the gene, and then 2 holes that line up between the boxes for the dimmer wires. To finish off the wiring in the pattress boxes, simply finish wiring the dimmer to the 2 way switch as shown below (click to enlarge). After some time using this modification, I have decided to drill some extra ventilation holes in the rear of the pattress box, using the existing push out points.
            Image
            and don’t forget to add cable ties inside/outside of holes to prevent wires pulling/being pushed through
            Image
            Screw everything together and add some duck tape to form the 2 separate pattress boxes into a single unit. I found this better than glue, which simply slides off and is messy. It also allows you to separate them in future if desired. Label your switch DIM and DIR, dimmer and direct….The finished roaster
            Image
            Just to ensure it's clear exactly how things were wired a very simple schematic of the circuit
            Image
            Usage
            I start my roasts with the Gene set to 240C and the switch in the DIR position, so that the dimmer is not being used and for at least the first 5 minutes and possibly up to 1st crack, I won’t be using the dimmer module.

            As soon as I want to control the temperature or slow the ramp, I switch to DIM and start using the dimmer (which I leave initially in the fully bright position). I find that depending on the ambient temperature and the temperature I want to maintain my roast at….around 1050 to 1100 watts in winter (possibly 1000W in summer), is enough to maintain the temperature without the element switching on and off. My Gene temperature control knob is now simply a safety or limiter on the maximum temperature the roast can achieve.

            Note: don’t set the genes own temperature control too close to the desired temperature as if the Gene reaches it, it will switch off the element and drop nearly 3/4C, something we want to avoid (This is why I use 240C).

            So if your voltage is good, you can control part of the ramp up and certainly have a controlled drying stage if you want to….for beans which are reaching 1st a little rapidly again you can temper this. At and beyond 1st crack you can pretty much set whatever profile you desire. The temperature gradient within the drum when under dimmer control will be at the absolute minimum it can be.

            At the end of the roast, I switch back to direct to take the dimmer out of the circuit, because otherwise there will be a small voltage (50V) across the dimmer during the cooling cycle and as long as the Gene is physically plugged in..with no load on the Dimmer (dimmer requires a 200W minimum load), I am not sure if this will have any effect on the triac within the dimmer, it's unlikely but there is no point in taking chances. The other reason for having the two way switch, is that there is a 30W power loss within the dimmer, but of course NO power loss with the switch in "DIRECT" mode

            Initial results are very encouraging, roast quality is great, roasts are visually more even, especially on beans which tend to be a little uneven anyway. Careful inspection will show a significant reduction (or absence) of Divots, Tipping or scorching. Interestingly roasts can actually be heard entering second crack, but the bean does not seem as dark as it would usually be when this happens, indicating the possibility or a more even roast throughout the internal structure of the bean.
            Attachments
            Dimmer Stage one fig 11.jpg
            Dimmer Stage one fig 11.jpg (29.87 KiB) Viewed 27728 times
            Dimmer Stage one fig 10.jpg
            Dimmer Stage one fig 10.jpg (108.29 KiB) Viewed 27728 times
            Dimmer Stage one fig 9.jpg
            Dimmer Stage one fig 9.jpg (108.77 KiB) Viewed 27728 times
            Dimmer Stage one fig 8.jpg
            Dimmer Stage one fig 8.jpg (69.09 KiB) Viewed 27728 times
            Dimmer Stage one fig 7.jpg
            Dimmer Stage one fig 7.jpg (133.49 KiB) Viewed 27728 times
            Dimmer Stage one fig 6.jpg
            Dimmer Stage one fig 6.jpg (153.91 KiB) Viewed 27728 times
            Dimmer Stage one fig 5.jpg
            Dimmer Stage one fig 5.jpg (141.11 KiB) Viewed 27728 times
            Dimmer Stage one fig 4.jpg
            Dimmer Stage one fig 4.jpg (116.09 KiB) Viewed 27728 times
            Dimmer Stage one fig 3.jpg
            Dimmer Stage one fig 3.jpg (78.19 KiB) Viewed 27728 times
            Dimmer Stage one fig 2.jpg
            Dimmer Stage one fig 2.jpg (34.35 KiB) Viewed 27728 times
            Dimmer Stage one fig 1.jpg
            Dimmer Stage one fig 1.jpg (142.96 KiB) Viewed 27728 times
            Post Reply